Best Metric Tap Drill Chart Sizes
Best results for metric tap drill chart sizes
Screw Thread Gauge | Metric and SAE | Recommends Drill Bit & Tap Size (BCP675)
$8.95
$10.11
Amazon.com
Last update was on: November 24, 2024 4:00 am
- Quickly and accurately determine the screws size
- Recommends the drill bit or tap size needed for the screw
- Standard & Metric
- Constructed of thick hard plastic for lasting durability
- Smooth easy to clean surface that resists oil and grease
Fraction to Decimal Conversion Chart Indoor Magnet
Marine Bolt Supply Nut, Bolt & Screw Gauge Standard & Metric Coarse & Fine Diameter, Length & Thread Pitch (Red)
Nut and Bolt Thread Checker (Complete SAE/Inch and Metric Set) (Packs)
Stainlesstown Nut Bolt Thread Gauge (Blue)
$8.95
$13.34
Amazon.com
Last update was on: November 24, 2024 4:00 am
- Measures diameter, thread pitch & length of nuts, bolts & screws
- Measures fractional bolts from size #4 to 1" up to 7" long
- Measures metric bolts & screws from size 3mm to 22mm
- Made of very durable 1/4" thick hard plastic
- 1/4" thick x 8-3/4" Long x 3-3/8 Wide
Big Gator Tools V-DrillGuide Metric and Standard Size Portable Drilling Guide Kit
$49.90
$65.37
Amazon.com
Last update was on: November 24, 2024 4:00 am
- Standard Size: 17 drill sizes, from 1/8" to 3/8", in 1/64" increments
- Metric Size: 17 drill sizes - 3mm to 9.5mm in 0.5mm increments plus 3.3mm, 4.2mm and 6.8mm
- Use on flat surfaces, round parts, and corners, Alignment marks on guide to line up on center
- Non-plated material with light oil coating to prevent rust
- Special nickel alloyed steel heat treated for durability
Engineering Slide Chart – Screw Data Selector
$29.99
$36.89
Amazon.com
Last update was on: November 24, 2024 4:00 am
- The Ultimate Engineering Screw Chart - NEW VERSION
- Includes technical information from many of the quick references that are commonly found in the work areas of designers, engineers, and machinists.
- All of this information is compiled for both English (Imperial) and Metric systems in a single screw chart. MADE IN THE USA.
- A “MUST HAVE” for Engineers, Designers, Drafters, and Machinists
Century Drill & Tool 97204 High Carbon Steel National Pipe Tap, 1/2-14 NPT
Screw Chek’r SAE/ Inch Screw Thread Size Gauge (No. 1 to 5/16) 1/8 Inch Heavy Gauge Steel Screw Checker, Made in USA
$13.95
$18.27
Amazon.com
Last update was on: November 24, 2024 4:00 am
- Say goodbye to frustration with this easy to use, pocket sized tool. Do it yourselfers, handymen, and mechanics can save time and money by accurately identifying different types of screws the first time. This tool gives all the information needed to properly identify machine screws, wood screws, sheet metal screws, bolts, and even cotter pins and rivets.
- Identifies diameter, size, pitch, and length, with a tap drill chart for sizes ranging from No. 1 through 5/16 inch in NC, NF, and NS pitches. This tool can also be used to straighten bent screws and clean dirty or rusty threads.
Grip Thread Pitch Gauge MM & SAE
Nut & Bolt Thread Checker (Inch & Metric)
$32.65
$43.42
Amazon.com
Last update was on: November 24, 2024 4:00 am
- Each size has a nut and bolt checker on the same gauge. 26 male/female gauges - 14 inch & 12 metric.
- Thread sizes are permanently stamped onto each gauge (inch in red, metric in white)
- Inch gauges are clear zinc plated, metric gauges are black oxide.
- The individual gauges rotate freely on the wire cable for fast thread verification
- Wire cable with loop for convenient hanging
Irwin Tools3018002 Cobalt M-35 Metal Index Drill Bit Set, 29 Piece
Big Gator Tools V Tap and V Drill Guides – Complete tool set of 6 Guides
$159.99
$187.19
Amazon.com
Last update was on: November 24, 2024 4:00 am
- Automatically squares up the tap or drill with the surface.
- V-groove along the bottom of the guides allows for perpendicular alignment on round parts or corners
- Natural steel finish, non-plated, Portable, pocket-sized. Lifetime Manufacture Warranty
- Made from special nickel alloyed steel that is heat treated for durability
- 100% Made in the USA. Eliminates most tap breakage due to improper alignment!
Atlas Press Co Decimal Equivalents Chart Machinist Lathe Tool Shop Poster
Metric Screw Checker (2mm to 7mm) – Made in USA
$14.95
$18.24
Amazon.com
Last update was on: November 24, 2024 4:00 am
- Say goodbye to frustration with this easy to use, pocket sized tool. Do-it-yourselfers, handymen, and mechanics can save time and money by accurately identifying different types of screws the first time. This tool gives all the information needed to properly identify machine screws, wood screws, sheet metal screws, bolts, and even cotter pins and rivets.
- Identifies diameter, size, pitch, and length, with a tap drill chart for metric screws from 2mm to 7mm. This tool can also be used to straighten bent screws and clean dirty or rusty threads.
